Login

7th European Steel Technology and Application Days - ESTAD 2025

6–9 Oct 2025
Palaexpo Veronafiere
Europe/Rome timezone
Conference Registration is open now!

Contact

Session

Forging

6
8 Oct 2025, 15:20
Mozart (Palaexpo Veronafiere)

Mozart

Palaexpo Veronafiere

Veronafiere, Viale del Lavoro 8, 37135 Verona

Conveners

Forging

  • Andrea Di Schino (University of Perugia)

Forging

  • Gerhard Hackl (ASMET)

Description

3.2.1

Presentation materials

There are no materials yet.

  1. 394. OEE improvement of TBB Forging mill
    Gabriele Lonzi (Cogne Acciai Speciali)
    08/10/2025, 15:20
    Forging
    Oral
  2. 362. ENERGY SAVING ON A 70 MN OPEN DIE FORGING PRESS
    Mr Mauro Baldassi (Danieli & C. Officine Meccaniche S.p.A.)
    08/10/2025, 15:40
    Forging
    Oral Presentation

    VID, acronym of Virtual Inertia Drive, is the new hydraulic drive that Danieli proposes in forging open die applications.
    His aim is to keep the same size and performances of a conventional forging machine, but reducing the total electrical power installed, the n° of motor-pumps unit and the energy consumption.
    System is made by the following components :
    1. Hydraulic...

    Go to contribution page
  3. 149. Effect of Intermediate Intercritical Quenching on Low Temperature Toughness of Low-alloy Steel Forgings
    Dr Ettore Anelli (Franchini Acciai SpA)
    08/10/2025, 16:30
    Forging
    Keynote Presentation

    Typical heat treatment of structural steel forgings consists of quenching and tempering (QT). However, in case of heavy forgings (thickness above 120 mm), made of steels with carbon content less than 0.25% and low hardenability, the required strength can be achieved, but low temperature impact toughness could be not fully adequate. In this work, an intermediate intercritical quenching (IIQ)...

    Go to contribution page
  4. 48. Advanced Ring Rolling Simulations with Embedded Machine Control Systems
    Dr Koos Van Putten (SMS group)
    08/10/2025, 16:50
    Forging
    Oral Presentation

    Radial axial (RAW) ring rolling is a well-established incremental forging process producing seamless rings and shells, both with rectangular as well as profiled cross sections, with high demands in terms of mechanical properties and microstructure, standing out for its productivity. Rolled rings and shells are applied in many industrial fields, e.g. wind power, nuclear industry, general...

    Go to contribution page
  5. 270. Optimization of Process Control and Energy Consumption in Hot Flat Ring Rolling Using Interactive Real-Time Software
    Mr Marco Munari (Project Group s.r.l.)
    08/10/2025, 17:10
    Forging
    Oral

    Hot Radial Axial Ring Rolling is a crucial process in seamless ring production for various industrial sectors, ranging from oil & gas to aerospace. To configure and optimize this complex process, modern rolling mills rely on computerized controls, where operators must input process parameters derived from multiple sources-including tables, formulas, experience, and time-consuming FEM...

    Go to contribution page
  6. 263. A combined experimental–numerical approach to assess the effects of quenching transfer time on the microstructure and mechanical properties of a Ti-6Al-4V alloy
    Dr Davide Maghini (Department of Engineering, University of Ferrara)
    08/10/2025, 17:30
    Forging
    Oral

    Nowadays, titanium (Ti) alloys play a pivotal role in aerospace and energy production sectors due to their specific mechanical properties. To date, the design of forged components in Ti alloys has been based on the experience of operators and engineers, and on the use of industrial tests to optimise production processes. However, the high production costs of these components and their possible...

    Go to contribution page
Building timetable...